Вот лог операции "Repair bad software"
COM10 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: repair "bad software"
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6223:8A04]...
CPU: MT6223
high speed boot enabled
chip: 0011:5D78:000C
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #01 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #02 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #03 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud...
230400
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #01 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
it's time to stop: 2A0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 00800000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: TOP23_07A_PCB01_GPRS_MT6223_S00.N1112_V5_53.BIN
ver. sw2: N1112_V5.53, 00000000
ffs offset/size: 00700000/00100000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting firmware protection...
detecting firmware structure #8...
phase #1...
................................
phase #2...
....................
done
detecting firmware structure #9...
detecting area #1...
....................
area #1 is Ok
done
detecting firmware protection done
Finished, time used: 35 sec
Remove/Install battery now !
2 шаг
COM10 [VCP0] selected
Action: repair "bad software"
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6223:8A04]...
CPU: MT6223
high speed boot enabled
chip: 0011:5D78:000C
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6223,E04
Date: 2000.00.00
Version: 1.0
Version: N1112_V5.53
Version:
detecting structure #2...
0 done
44 byte(s) read
imei: 35958601000084
connection Ok
detecting structure #6 (mode-1)...
0 done
181 byte(s) read
writing data...
verification...
verification Ok
Finished, time used: 10 sec
Remove/Install battery now !
при включении пишет "Bad software"