Помогите найти фулл на BBK i399

[david19]

Помогите найти фулл на BBK i399 под flash Tool, тел с одной сим картой, на проце 6228.
надо была сделать русификацию, слил с помощю infinity бекап ,версия прошивки была BBK28_06B_PCB04_GPRS_MT6228_S02.BBK ,скачал с сапорта прошивку K322_BBK28_06B_PCB04_GPRS_MT6228_S02[1].ББК_2008-07-14_Ен_Ру.Б4М и прошил, телефон после етого не включился,Хочу залит бекап, не получается.
вот лог
==== log: [12.05.2009 18:23:58] ====
COM5 [VCP0] selected
module v2.80
Device: Autodetect 6228-6230 NAND
Checking data, wait...
Action: write NAND flash
read mode: 01
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw 1: BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN
ver. sw 2: BBK, 1AA8E02D
ffs offset/size: 02000000/06000000
id-page1 Ok
end mark #1 found
nfi area detection finished: Ok
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6228:8A02:8A02]...
CPU: MT6228
high speed boot On
chip: 0031C09:0101
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.0207
loader: 3.748.0
NAND id: 98F19095
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
finalize connection...
done
emi configuration...
ram size: 00800000
emi configuration done
check bootloader validity...
done
NOR: 0000:000000000000 [00000000]
NAND: 0098:00F100900095 [08400000]
NOR chip is not installed
Initialize Done
Set baud ...
460800
Set baud Done
Identification ...
reading bootloader structure area (00080000 bytes)...
detecting bootloader structure...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN
ver. sw 2: BBK, 1AA8E02D
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
detecting bootloader structure by source file...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN
ver. sw 2: BBK, 1AA8E02D
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is damaged, recalculation required
identification#1 detection finished
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.E767D607.[BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN_D21F57E5].rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.E767D607._BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN_D21F57E5_.rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.E767D607.[BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN_D21F57E5].rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.E767D607._BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN_D21F57E5_.rpl
====================
warning: unknown identification#1 structure: BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN_D21F57E5
error: Unknown firmware detected (v.2.80, database date: ), user action required:
1. download latest software from support area and try again
2. if no still luck follow the next procedure:
- find good working phone with the same firmware:
BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN
- make "Read full flash" operation
- send "system_log_..." file to support: mt62xx@gmail.com
- send flash backup files to support: mt62xx@gmail.com
- include in your e-mail full text from phone back label (phone name etc.)
- be little bit patient and wait update
====================
You can flash phone now but can not finalize it.
In most cases phone CAN NOT power-on.
Do you want to continue anyway ?
Identification Done
Write ...
00006000 bytes sent
write core area 1 of 3...
00413C00 bytes sent
write core area 2 of 3...
00CAB000 bytes sent
write core area 3 of 3...
002EE800 bytes sent
Write Done
Finished, time used: 725 sec
Remove/Install battery now !

отправил на mt62xx@gmail.com лог и сделанный бекап , но нет ответа уже 4 дня.

 

[david19]

с телефоном разобрался тему можно закрыть