Chinase miraclе
COM18 [Serial2] selected
module v3.20
Device: Autodetect 6205-6239 NOR
Checking data, wait...
advanced flash detection enabled
Action: "user code"
unlock method: standard fast
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A05:8A00]...
CPU: MT6223
high speed boot On
chip: 0011:727A:000C
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
====> Initialize ...
detecting chip #00 in region #00...
flash: 01227E22202200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
otp offset: 00000000
detecting chip #01 in region #00...
flash: 01227E22202200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
otp offset: 00000000
detecting chip #02 in region #00...
flash: 01227E22202200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
otp offset: 00000000
detecting chip #03 in region #00...
flash: 01227E22202200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
otp offset: 00000000
number of flash chip/regions detected: 04/01
Initialize Done
====> Set baud ...
921600
Set baud Done
====> Initialize bootcode ...
Initialize bootcode Done
====> Check firmware integrity ...
device parameters detection in progress...
detecting chip #00 in region #00...
flash: 01227E22202200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
otp offset: 00000000
detecting chip #01 in region #00...
flash: 01227E22202200:2CEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
otp offset: 00000000
it's time to stop: 2C0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
usb bootloader detect...
..
usb bootloader detect (phase #2)...
..
usb bootloader (chip) is absent
searching rom info...
warning: wrong cs at 0x00000B90, retry...
warning: wrong cs at 0x00000B90, retry...
warning: wrong cs at 0x00000B90, retry...
warning: wrong cs at 0x00000B90, retry...
warning: wrong cs at 0x00000B90, retry...
warning: wrong cs at 0x00000B90, retry...
read error recovered
warning: wrong data size at 0x00001B90, retry...
warning: wrong cs at 0x00001B90, retry...
warning: wrong cs at 0x00001B90, retry...
warning: wrong cs at 0x00001B90, retry...
warning: wrong cs at 0x00001B90, retry...
read error recovered
mmodule 3.62
COM18 [Serial2] selected
module v3.62
Action: read unlock codes
unlock method: read codes
Model: Fly-E135
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:727A:000C
status: FF
Connecting at 19200, wait...
дальше телефон включется и экран становится белым, ползунок идет до конца и .....
error: can not finalize test mode
repeat operation and HOLD phone "Power" button more long time !
error: operation failed !
Finished, time used: 13 sec
Remove/Install battery now !