C7-00 не включается после прошивки

Zohan7787 · 14/7/12

Пришол с7-00 с битом симлоком заказали рпл, сделали эрасе тепер он не прошиваештся бестом и цеклолоном. флэш поменял прошил тоже самое. в начале пробовали залить рпл, проходит до сим лока (отказ в сим локе) тепер он вообше не прошивается, уфс прошивает а цеклон и бест не прошивается!!! далее помогите ребята в чём может быть проблема?? зарание спасибо!!

xaker2010 · 14/7/12

а логи виложити

Nazhmudin · 14/7/12

До заказа рпл Вы работоспособность т.а со стиранием и прошивкой проверяли?Хоть имей кривой но должен нормально работать пару минут.

---------- Сообщение добавлено в 12:13 ---------- Предыдущее сообщение было от в 12:11 ----------

И прошивку какую заливали в телефон belle или anna?

Zohan7787 · 14/7/12

вот вам лог
Пришел стертый телефон. Заказал RPL. Прошил, тел. включился. Не могу пролить симлок.

Skipping RPL decryption...
Parsing decrypted RPL...
Processing FBUS Part...
Writing Simlock...
Handling as SL3 Simlock Data
Handling as SIMLOCK2 Format
Reading Security Block...
Security block OK and saved to "RM-675_353755043426719_14.07.2012_133716.SecurityBloc k.PM"
15 Digits NCK Found
Simlock ACCEPTED OK !
Writing Superdongle key...
Superdongle Key ACCEPTED OK !
Writing CMLA key...
CMLA Key NOT ACCEPTED !
Writing WMDRM PD Data...
WMDRM PD Data NOT ACCEPTED !
Processing FLASHBUS Part...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 0FD00005B09C0344267ED78F8D67C076A0FE409C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.48.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC006800000131, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0068 (Samsung), Size: 1024MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.48.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 95A68E9FA27B2BFA89EA204FC846EB73DEF1D93F
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
CMT NPC Erased
CMT NPC Written
CMT HWC Erased
CMT HWC Written
CMT CCC Erased
CMT CCC Written
Restarting MCU...
Write RPL Finished!
Started Phone Security Analysis...
MCU Version V 92_11w37
MCU Date 14-09-11
Product RM-675 (Nokia C7-00)
Manufacturer (c) Nokia
IMEI 353755043426719
Mastercode 4047231520
Reading Security Block...
Security block OK and saved to "RM-675_353755043426719_14.07.2012_133733.SecurityBloc k.PM"
Step 1 : Testing SIMLOCK
-- SIMLOCK PROBLEM --

Phone have failed SIMLOCK Test, that means Simlock Area is DAMAGED!
To repair simlock area, Select Unlock method : "RPL CALCULATION",
And then click DIRECT UNLOCK. SL Area will be re-formatted.

-- SIMLOCK PROBLEM --
Step 2 : Testing SECURITY
-- SECURITY PROBLEM --

Phone have failed SECURITY Test, that means Superdongle Area is DAMAGED!
To repair it, simply slick "SX4 Authorization / SD Repair" button.
After SX4/SD Repair, don't forget to write PM file with fields 1,309 (if SW don't do this automatically)

Additionaly, Checking HWC/CCC Certs...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 0FD00005B09C0344267ED78F8D67C076A0FE409C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.48.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC006800000131, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0068 (Samsung), Size: 1024MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.48.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 95A68E9FA27B2BFA89EA204FC846EB73DEF1D93F
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
HWC Looks OK!
CCC Looks OK!
Restarting MCU...
-- SECURITY PROBLEM --
Step 3 : Analyzing Security Block
"0FD00005B09C0344267ED78F8D67C076A0FE409C.C0001693 " Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
CMLA KEYS FOUND AND CHECKSUM OK! PASSED!
Checking ECC KEYS...
ECC KEYS FOUND AND CHECKSUM OK! PASSED!
Checking DIV KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Analyze finished!

---------- Сообщение добавлено в 12:30 ---------- Предыдущее сообщение было от в 12:29 ----------

я прошиваю анну

---------- Сообщение добавлено в 13:06 ---------- Предыдущее сообщение было от в 12:30 ----------

Skipping RPL decryption...
Parsing decrypted RPL...
Processing FBUS Part...
Writing Simlock...
Handling as SL3 Simlock Data
Handling as SIMLOCK2 Format
Reading Security Block...
Security block OK and saved to "RM-675_353755043426719_14.07.2012_133716.SecurityBloc k.PM"
15 Digits NCK Found
Simlock ACCEPTED OK !
Writing Superdongle key...
Superdongle Key ACCEPTED OK !
Writing CMLA key...
CMLA Key NOT ACCEPTED !
Writing WMDRM PD Data...
WMDRM PD Data NOT ACCEPTED !
Processing FLASHBUS Part...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 0FD00005B09C0344267ED78F8D67C076A0FE409C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.48.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC006800000131, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0068 (Samsung), Size: 1024MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.48.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 95A68E9FA27B2BFA89EA204FC846EB73DEF1D93F
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
CMT NPC Erased
CMT NPC Written
CMT HWC Erased
CMT HWC Written
CMT CCC Erased
CMT CCC Written
Restarting MCU...
Write RPL Finished!
Started Phone Security Analysis...
MCU Version V 92_11w37
MCU Date 14-09-11
Product RM-675 (Nokia C7-00)
Manufacturer (c) Nokia
IMEI 353755043426719
Mastercode 4047231520
Reading Security Block...
Security block OK and saved to "RM-675_353755043426719_14.07.2012_133733.SecurityBloc k.PM"
Step 1 : Testing SIMLOCK
-- SIMLOCK PROBLEM --

Phone have failed SIMLOCK Test, that means Simlock Area is DAMAGED!
To repair simlock area, Select Unlock method : "RPL CALCULATION",
And then click DIRECT UNLOCK. SL Area will be re-formatted.

-- SIMLOCK PROBLEM --
Step 2 : Testing SECURITY
-- SECURITY PROBLEM --

Phone have failed SECURITY Test, that means Superdongle Area is DAMAGED!
To repair it, simply slick "SX4 Authorization / SD Repair" button.
After SX4/SD Repair, don't forget to write PM file with fields 1,309 (if SW don't do this automatically)

Additionaly, Checking HWC/CCC Certs...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 0FD00005B09C0344267ED78F8D67C076A0FE409C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.48.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC006800000131, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0068 (Samsung), Size: 1024MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.48.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 95A68E9FA27B2BFA89EA204FC846EB73DEF1D93F
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
HWC Looks OK!
CCC Looks OK!
Restarting MCU...
-- SECURITY PROBLEM --
Step 3 : Analyzing Security Block
"0FD00005B09C0344267ED78F8D67C076A0FE409C.C000 1693 " Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
CMLA KEYS FOUND AND CHECKSUM OK! PASSED!
Checking ECC KEYS...
ECC KEYS FOUND AND CHECKSUM OK! PASSED!
Checking DIV KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Analyze finished!

nkman1 · 14/7/12

Пролейте последнюю версию. Т.е. беллу. 111.30.609 - версия

Zohan7787 · 14/7/12

прошиваю анну

---------- Сообщение добавлено в 13:12 ---------- Предыдущее сообщение было от в 13:10 ----------

пробиваю белу тоже самое

---------- Сообщение добавлено в 13:14 ---------- Предыдущее сообщение было от в 13:12 ----------

-- SIMLOCK PROBLEM --
Step 2 : Testing SECURITY
-- SECURITY PROBLEM --

ilyuw · 14/7/12

с перва надо сделать RPL через best потом уж надо стирать, и потом можете прошивать какую вы хотите

Zohan7787 · 14/7/12

я и так делал дело вот вчём он сим лок не пробивает

ilyuw · 14/7/12

тогда лучше другую мату поставь

Zohan7787 · 14/7/12

да легко говорить я купил рпл и еше в добавку мать

---------- Сообщение добавлено в 13:33 ---------- Предыдущее сообщение было от в 13:27 ----------

да легко говорить я купил рпл и еше в добавку мать

ilyuw · 14/7/12

да уж тебе не везет

Zohan7787 · 14/7/12

всем спасибо тема закрыта

GIZO · 14/7/12

вопрос решен или вы просто вернули ТА?

sergo-k · 15/7/12

nokia 2700 после воды не включается что делать ?

Yilmaz · 15/7/12

почистит тело и прогрет проц, betty и awilma конечно с флюсом

Профессионал · 15/7/12

sergo-k сказал(а):
купите доступ для просмотра контента

прочитать ПРАВИЛА форума, создать Тему в соответствующем разделе!

voron300 · 16/7/12

ilyuw сказал(а):
купите доступ для просмотра контента

Пусть меня опять накажут, но это полная хр.нь

---------- Сообщение добавлено в 01:07 ---------- Предыдущее сообщение было от в 01:02 ----------

ilyuw сказал(а):
купите доступ для просмотра контента

Сколько стоит мать? Она на каждом углу не продается. А если она стоит как RPL, значит угнаная! Уважаемый, вы мастер или ГДЕ?

---------- Сообщение добавлено в 01:11 ---------- Предыдущее сообщение было от в 01:07 ----------

GIZO сказал(а):
купите доступ для просмотра контента

Вопрос не решен. Данная тема обсуждается на форуме

купите доступ для просмотра контента

Zohan7787 · 16/7/12

я та не вернул так что до сих пор мучаюсь

JayDi · 17/7/12

RPL'ы в личку, поглядеть.

nkman1 · 17/7/12

Если есть рпл может стоить попробовать первые прошивки влить? Чем черт не шутит.

voron300 · 18/7/12

JayDi сказал(а):
купите доступ для просмотра контента

Не пойму как в личке вставить файл

Tolian97 · 19/7/12

Залейте на файл обменник а ссылку отправте в личку

C7-00 не включается после прошивки

Zohan7787

xaker2010

Nazhmudin

Zohan7787

nkman1

Zohan7787

ilyuw

Zohan7787

ilyuw

Zohan7787

ilyuw

Zohan7787

GIZO

sergo-k

Yilmaz

Профессионал

voron300

Zohan7787

JayDi

Infinity Box

nkman1

voron300

Tolian97

Похожие Темы