Вопрос не могу обновить FW KMRP60014M - Software install corrupted!

[andreys63]

KMRP60014M пытаюсь восстановить с помощью TP
FW - скачал на этом форуме. В список добавил правильно.
Win7 32. Антивирус отключал. Программу Z3X EasyJtag переустанавливал.

Ошибка - Software install corrupted!

как победить?

вот логи

Z3X EasyJtag Software ver. 3.7.0.20
Loading eMMC GEN2 Firmware... IO: 2800 mV
Initial pull results:
clock: 1514mV pin connected ok
command: 1726mV pin connected ok
data0: 1337mV pin connected ok
data1: 1334mV pin connected ok
data2: 1337mV pin connected ok
data3: 1337mV pin connected ok
data4: 1336mV pin connected ok
data5: 1337mV pin connected ok
data6: 1335mV pin connected ok
data7: 1336mV pin connected ok
Box S/N: 38DF468A730C4062, ,FW Ver.: 02.53
Box IO Level:2800 mV
CLK Rate:14000 kHz
Bus Width:8bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------

eMMC CID : 150100303030303030562016061354D1
eMMC CSD : 902701320F5903FFF6DB7FE08A40403B
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 05/2017 Rev.0x56
eMMC NAME: 000000 , S/N: 538314259
eMMC NAME (HEX): 303030303030
EMMC ROM1 (Main User Data) Capacity: 2095982 MB
EMMC ROM2 (Boot Раздел 1) Емкость: 512 kB
EMMC ROM3 (Boot Раздел 2) Емкость: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC RPMB is not yet programmed (clear) or RPMB General failure
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: 000000_ 538314259_20230114_1328.extcsd
Blocks Reading Error (0x0 , 1 , Reason: DATA RCV Timeout Error )
Blocks Reading Error (0x200 , 1 , Reason: DATA RCV Timeout Error )
Warning! Read error 0 strange behavior now likely!
Blocks Reading Error (0x1FFB6DFFE00 , 1 , Reason: DATA RCV Timeout Error )
Warning! Read error 0 strange behavior now likely!
Partition info not found
Сделано.

Running:SAMSUNG: eMMC firmware update...
Init OK...
Confirmed eMMC Part Number: KMRP60014A-B614
Checking security ...
Z3X EasyJtag Software ver. 3.7.0.20
Software install corrupted!
Сделано.

 

[Radiotrance]

Для начала поставить последнюю версию.

 

[andreys63]

Z3X EasyJtag Software ver. 3.7.0.20 - брал в shell.
есть другие версии?

 

[kwb]

3.7.0.24 последняя

 

[andreys63]

а можно ссылку где качнуть?
shell - вообще не актуален?

все. отбой. нашел новую версию. буду пробовать