День добрый!
Принесли n85, сбит сим-лок, лог прилагаю:
MCU Version V ICPR72_09w18.6
MCU Date 15-10-09
Product RM-333 (Nokia N85)
Manufacturer (c) Nokia
IMEI 356376027983364
Mastercode 32234664
IMEI Spare 3A65730672893306
IMEI SV 3365730672893316F0000000
PSN CSF012267
Product Code 0561252
Basic Product Code 0560428
PSD 0000000000000000
LPSN 0
WLAN MAC 347E39BAA63C
APE SW 31.002
APE Variant 31.00231.002.005.131.002.53.1
APE Test eno_version
APE HW 256
APE ADSP 256
RETU 15
TAHVO 22
AHNE 11
HW 1400
RFIC |Vapaus_5.1 | ???
DSP wmps.ICPR72_09w17_p1
Failed to read info -> Failed to read SP info
Если нажимаю Check Flashing Bus то зависает, после слов про TX2 адаптер. Если ставлю галочку использовать OLD Protocol Layers (не убирая галочку напротив TX2, то Check Flasing Bus проходит нормально:
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103
CMT_EM_ASIC_ID: 00000295
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 068001116180005261C3145F51B9415047B7040C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit (Forcing OLD Protocol)
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.37.1, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC004000800121, Samsung, ONENAND
FlashContent[0,CMT]: 00000000000000000000000000000000, ONENAND
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit (Forcing OLD Protocol)
FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
RAPIDOv11_algo.fg, Type: Algorithm, Rev: 0.1.40.0, Algo: XSR 1.5
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: B5385A493D2188678E1FD88DA506480F874E2949
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Restarting MCU...
Это телефон SL2, соответственно пробую поправить сим-лок через вкладку Simlocks используя Direct Unlock - и тут процесс не получается - вот лог:
BB5 Unlock Started...
MCU Version V ICPR72_09w18.6
MCU Date 15-10-09
Product RM-333 (Nokia N85)
Manufacturer (c) Nokia
IMEI 356376027983364
Mastercode 32234664
Warning: Failed to read SP Info, Assuming defaults
Simlock Server SIMLOCK SERVER
Simlock Key 0000000000000000
Simlock Profile
Simlock Key Cnt 0
Simlock FBUS Cnt 0
Reading Security Block...
Security block OK and saved to "RM-333_356376027983364_29.04.2012_132511.SecurityBlock.PM"
WARNING: "068001116180005261C3145F51B9415047B7040C" Not Exists, Will read it...
Reading CYC file from phone...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103
CMT_EM_ASIC_ID: 00000295
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 068001116180005261C3145F51B9415047B7040C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
New_RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.16.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
CBUS Request Error -> CBUS Response wrong header
Prepare phone failed with message -> Failed to get CMT Configuration
Neither CYC file and exists or failed to read it from phone (Failed to Boot / Prepare Phone)
BB5 Unlock Failed -> Failed to obtain Phone Unique Data
Я правильно понимаю, что при разлочку при этом используются "новые" протоколы и игнорируется галочку использовать старые?
p.s. Кабель - универсальная 7-пиновая прищепка
---------- Сообщение добавлено в 14:29 ---------- Предыдущее сообщение было от в 13:27 ----------
насчет TX2 переходника - я переделал сам бокс - разрезал 2 проводника внутри и бросил 2 перемычки - т.е. по идее проблем быть не должно(?)
Пробовал до переделки и после переделки - результат один и тот же - чек проходит только при галочке использовать старый протокол.
Принесли n85, сбит сим-лок, лог прилагаю:
MCU Version V ICPR72_09w18.6
MCU Date 15-10-09
Product RM-333 (Nokia N85)
Manufacturer (c) Nokia
IMEI 356376027983364
Mastercode 32234664
IMEI Spare 3A65730672893306
IMEI SV 3365730672893316F0000000
PSN CSF012267
Product Code 0561252
Basic Product Code 0560428
PSD 0000000000000000
LPSN 0
WLAN MAC 347E39BAA63C
APE SW 31.002
APE Variant 31.00231.002.005.131.002.53.1
APE Test eno_version
APE HW 256
APE ADSP 256
RETU 15
TAHVO 22
AHNE 11
HW 1400
RFIC |Vapaus_5.1 | ???
DSP wmps.ICPR72_09w17_p1
Failed to read info -> Failed to read SP info
Если нажимаю Check Flashing Bus то зависает, после слов про TX2 адаптер. Если ставлю галочку использовать OLD Protocol Layers (не убирая галочку напротив TX2, то Check Flasing Bus проходит нормально:
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103
CMT_EM_ASIC_ID: 00000295
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 068001116180005261C3145F51B9415047B7040C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit (Forcing OLD Protocol)
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.37.1, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC004000800121, Samsung, ONENAND
FlashContent[0,CMT]: 00000000000000000000000000000000, ONENAND
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit (Forcing OLD Protocol)
FlashChip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported
RAPIDOv11_algo.fg, Type: Algorithm, Rev: 0.1.40.0, Algo: XSR 1.5
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: B5385A493D2188678E1FD88DA506480F874E2949
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Restarting MCU...
Это телефон SL2, соответственно пробую поправить сим-лок через вкладку Simlocks используя Direct Unlock - и тут процесс не получается - вот лог:
BB5 Unlock Started...
MCU Version V ICPR72_09w18.6
MCU Date 15-10-09
Product RM-333 (Nokia N85)
Manufacturer (c) Nokia
IMEI 356376027983364
Mastercode 32234664
Warning: Failed to read SP Info, Assuming defaults
Simlock Server SIMLOCK SERVER
Simlock Key 0000000000000000
Simlock Profile
Simlock Key Cnt 0
Simlock FBUS Cnt 0
Reading Security Block...
Security block OK and saved to "RM-333_356376027983364_29.04.2012_132511.SecurityBlock.PM"
WARNING: "068001116180005261C3145F51B9415047B7040C" Not Exists, Will read it...
Reading CYC file from phone...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103
CMT_EM_ASIC_ID: 00000295
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 068001116180005261C3145F51B9415047B7040C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC: 4B9B7510
CMT_SECURE_ROM_CRC: 3E691FF8
CMT Ready!
New_RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.16.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
CBUS Request Error -> CBUS Response wrong header
Prepare phone failed with message -> Failed to get CMT Configuration
Neither CYC file and exists or failed to read it from phone (Failed to Boot / Prepare Phone)
BB5 Unlock Failed -> Failed to obtain Phone Unique Data
Я правильно понимаю, что при разлочку при этом используются "новые" протоколы и игнорируется галочку использовать старые?
p.s. Кабель - универсальная 7-пиновая прищепка
---------- Сообщение добавлено в 14:29 ---------- Предыдущее сообщение было от в 13:27 ----------
насчет TX2 переходника - я переделал сам бокс - разрезал 2 проводника внутри и бросил 2 перемычки - т.е. по идее проблем быть не должно(?)
Пробовал до переделки и после переделки - результат один и тот же - чек проходит только при галочке использовать старый протокол.
