пришел с уваленным бутом! Подцепил Riffом как 9100 внизу Jtag pinout выложил вдруг понадобится! Теперь вот какой вопрос! При востановлении он говорит:
Initiate Download Mode
Resurrect by flashing SPL
Выбираю первый метод выходит это:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.30, JTAG Manager Version: 1.37
Selected Resurrector: [Samsung i9100]
Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 2 MHz
Initializing internal hardware configuration...OK
Uploading selected SPL code into RAM...OK
Executing the uploaded SPL code...FAILED
ERROR: DCC Loader Execute failed. Terminating.
Выбираю 2 метод выходит вот что:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.30, JTAG Manager Version: 1.37
Selected Resurrector: [Samsung i9100]
Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.80V, TCK Frequency is 2 MHz
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Потом:
Resurrection write was interrupted
A previous Resurrection operation has failed in the middle
Do you want to continue resurrection from the interruption point or begin from start?
И что бы я не нажимал пишет:
WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x00000000
ERROR: Selected FLASH Chip was not initialized by the DCC Loader.
Подскажите где можно взять DCC Loader или как ввести в него адресса! Если известен адресс то как инструкциями поделитесь. Спасибо заранее! :icq01:
http://forum.**************/vbb/attachment.php?attachmentid=264027&d=1312499663
PS: Модераторы перезалейте Плз картинку я так и не смог его откорректировать на компе! Прошу прошения!
Initiate Download Mode
Resurrect by flashing SPL
Выбираю первый метод выходит это:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.30, JTAG Manager Version: 1.37
Selected Resurrector: [Samsung i9100]
Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 2 MHz
Initializing internal hardware configuration...OK
Uploading selected SPL code into RAM...OK
Executing the uploaded SPL code...FAILED
ERROR: DCC Loader Execute failed. Terminating.
Выбираю 2 метод выходит вот что:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.30, JTAG Manager Version: 1.37
Selected Resurrector: [Samsung i9100]
Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.80V, TCK Frequency is 2 MHz
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Потом:
Resurrection write was interrupted
A previous Resurrection operation has failed in the middle
Do you want to continue resurrection from the interruption point or begin from start?
И что бы я не нажимал пишет:
WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x00000000
ERROR: Selected FLASH Chip was not initialized by the DCC Loader.
Подскажите где можно взять DCC Loader или как ввести в него адресса! Если известен адресс то как инструкциями поделитесь. Спасибо заранее! :icq01:
http://forum.**************/vbb/attachment.php?attachmentid=264027&d=1312499663
PS: Модераторы перезалейте Плз картинку я так и не смог его откорректировать на компе! Прошу прошения!
