i9190 тел не заходить в режим загрузки поменял память от i8190 и стер все и через direct emmc залил I9190XXUBNA1 сервис но та не хочет войти в режим загрузки. Но у меня нету atf чтоб зайти через sdc- . помогите что делать как зайти в режим загрузки вот лог
Z3X EasyJtag Software ver. 2.0.6.8
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: -----------------, ,FW Ver.: 01.52
CMD Pullup Level:1144 mV
CMD Active Level:1629 mV
eMMC Device Information
EMMC CID : 45010053454D3038479008C30EE39036
EMMC CSD : D00F00320F5903FFFFFFFFFF92404010
EMMC Manufacturer ID: 0045 , OEM ID: 0100
EMMC Date: 09/2013 Rev.0x90
EMMC NAME: SEM08G , S/N: 147001059
EMMC NAME (HEX): 53454D30384700
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
Backup saved: SEM08G_ 147001059_20160121_1315.extcsd
Searching for partition tables...
Detected GPT over MBR...
Medium UUID: 98101B32-BBE2-4BF2-A06E-2BB33D000C20
Warning: Entries Count = 128
MMCBLK0P0 (MODEM) Range: [0X400000,0X3FFFE00] ,Len: 3C00000
MMCBLK0P1 (SBL1) Range: [0X4000000,0X401FE00] ,Len: 20000
MMCBLK0P2 (SBL2) Range: [0X4020000,0X405FE00] ,Len: 40000
MMCBLK0P3 (SBL3) Range: [0X4060000,0X40DFE00] ,Len: 80000
MMCBLK0P4 (ABOOT) Range: [0X40E0000,0X42DFE00] ,Len: 200000
MMCBLK0P5 (RPM) Range: [0X42E0000,0X435FE00] ,Len: 80000
MMCBLK0P6 (TZ) Range: [0X4360000,0X43DFE00] ,Len: 80000
MMCBLK0P7 (PAD) Range: [0X43E0000,0X505FE00] ,Len: C80000
MMCBLK0P8 (PARAM) Range: [0X5060000,0X585FE00] ,Len: 800000
MMCBLK0P9 (EFS) Range: [0X5860000,0X65FFE00] ,Len: DA0000
MMCBLK0P10 (MODEMST1) Range: [0X6600000,0X68FFE00] ,Len: 300000
MMCBLK0P11 (MODEMST2) Range: [0X6900000,0X6BFFE00] ,Len: 300000
MMCBLK0P12 (BOOT) Range: [0X6C00000,0X75FFE00] ,Len: A00000
MMCBLK0P13 (RECOVERY) Range: [0X7600000,0X7FFFE00] ,Len: A00000
MMCBLK0P14 (FOTA) Range: [0X8000000,0X89FFE00] ,Len: A00000
MMCBLK0P15 (BACKUP) Range: [0X8A00000,0X90FDE00] ,Len: 6FE000
MMCBLK0P16 (FSG) Range: [0X90FE000,0X93FDE00] ,Len: 300000
MMCBLK0P17 (SSD) Range: [0X93FE000,0X93FFE00] ,Len: 2000
MMCBLK0P18 (PERSIST) Range: [0X9400000,0X9BFFE00] ,Len: 800000
MMCBLK0P19 (PERSDATA) Range: [0X9C00000,0XA7FFE00] ,Len: C00000
MMCBLK0P20 (SYSTEM) Range: [0XA800000,0X683FFE00] ,Len: 5DC00000
MMCBLK0P21 (CACHE) Range: [0X68400000,0X74BFFE00] ,Len: C800000
MMCBLK0P22 (HIDDEN) Range: [0X74C00000,0X757FFE00] ,Len: C00000
MMCBLK0P23 (USERDATA) Range: [0X75800000,0X1D1FFBC00] ,Len: 15C7FBE00
Done...Presets has been updated...
Done.
Z3X EasyJtag Software ver. 2.0.6.8
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: -----------------, ,FW Ver.: 01.52
CMD Pullup Level:1144 mV
CMD Active Level:1629 mV
eMMC Device Information
EMMC CID : 45010053454D3038479008C30EE39036
EMMC CSD : D00F00320F5903FFFFFFFFFF92404010
EMMC Manufacturer ID: 0045 , OEM ID: 0100
EMMC Date: 09/2013 Rev.0x90
EMMC NAME: SEM08G , S/N: 147001059
EMMC NAME (HEX): 53454D30384700
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
Backup saved: SEM08G_ 147001059_20160121_1315.extcsd
Searching for partition tables...
Detected GPT over MBR...
Medium UUID: 98101B32-BBE2-4BF2-A06E-2BB33D000C20
Warning: Entries Count = 128
MMCBLK0P0 (MODEM) Range: [0X400000,0X3FFFE00] ,Len: 3C00000
MMCBLK0P1 (SBL1) Range: [0X4000000,0X401FE00] ,Len: 20000
MMCBLK0P2 (SBL2) Range: [0X4020000,0X405FE00] ,Len: 40000
MMCBLK0P3 (SBL3) Range: [0X4060000,0X40DFE00] ,Len: 80000
MMCBLK0P4 (ABOOT) Range: [0X40E0000,0X42DFE00] ,Len: 200000
MMCBLK0P5 (RPM) Range: [0X42E0000,0X435FE00] ,Len: 80000
MMCBLK0P6 (TZ) Range: [0X4360000,0X43DFE00] ,Len: 80000
MMCBLK0P7 (PAD) Range: [0X43E0000,0X505FE00] ,Len: C80000
MMCBLK0P8 (PARAM) Range: [0X5060000,0X585FE00] ,Len: 800000
MMCBLK0P9 (EFS) Range: [0X5860000,0X65FFE00] ,Len: DA0000
MMCBLK0P10 (MODEMST1) Range: [0X6600000,0X68FFE00] ,Len: 300000
MMCBLK0P11 (MODEMST2) Range: [0X6900000,0X6BFFE00] ,Len: 300000
MMCBLK0P12 (BOOT) Range: [0X6C00000,0X75FFE00] ,Len: A00000
MMCBLK0P13 (RECOVERY) Range: [0X7600000,0X7FFFE00] ,Len: A00000
MMCBLK0P14 (FOTA) Range: [0X8000000,0X89FFE00] ,Len: A00000
MMCBLK0P15 (BACKUP) Range: [0X8A00000,0X90FDE00] ,Len: 6FE000
MMCBLK0P16 (FSG) Range: [0X90FE000,0X93FDE00] ,Len: 300000
MMCBLK0P17 (SSD) Range: [0X93FE000,0X93FFE00] ,Len: 2000
MMCBLK0P18 (PERSIST) Range: [0X9400000,0X9BFFE00] ,Len: 800000
MMCBLK0P19 (PERSDATA) Range: [0X9C00000,0XA7FFE00] ,Len: C00000
MMCBLK0P20 (SYSTEM) Range: [0XA800000,0X683FFE00] ,Len: 5DC00000
MMCBLK0P21 (CACHE) Range: [0X68400000,0X74BFFE00] ,Len: C800000
MMCBLK0P22 (HIDDEN) Range: [0X74C00000,0X757FFE00] ,Len: C00000
MMCBLK0P23 (USERDATA) Range: [0X75800000,0X1D1FFBC00] ,Len: 15C7FBE00
Done...Presets has been updated...
Done.